At present, China's LED lighting industry is entering a period of independent innovation and achieving a leap-forward development. The application of LED street lamps has been expanding, but LED street lamps have encountered some problems in application practice. The whole country has become a testing ground for LED street lamps. Some products have no scientific and technological content, and low-level repeated construction. There are some problems in the application of LED street lamps to be solved.
1, the price is high
At present, the cost of LED street lamps is much higher than that of high-pressure sodium lamps. The price of an LED street lamp is 3,000-5,000 yuan or even higher, and the price of a set of imported high-pressure sodium lamps (including lamps and complete sets of electrical appliances) does not exceed 1,500 yuan. As far as the status quo is concerned, LED street lights are obviously too expensive, and the price is 2 to 5 times that of high-pressure sodium lamps. Therefore, even if the power consumption of the LED street lamp is only one-half of that of the high-pressure sodium lamp, since the price is much higher than that of the high-pressure sodium lamp, the cost recovery cycle of replacing the high-pressure sodium lamp with the LED street lamp is still very long.
Therefore, LED street lights should be officially promoted in the road lighting market, and the price and cost are still the biggest obstacles. To reduce the price of LED street lights to the price of existing lamps, the cost of each manufacturer needs to be reduced. In the near future, only under the premise of continuous maturity of LED technology and continuous improvement of luminous efficiency, LEDs have the advantages of life and energy saving to compensate for the disadvantages of lamp prices.
2, domestic light source can not meet the market demand
The development of domestic LED light sources started relatively late in foreign countries, and the technical level still has a certain distance from the international leading players. At present, the luminous efficiency of imported light sources such as Cree, Nichia and Osram is generally more than 100 lm/W. Although the domestic development of LED light source technology has been continuously invested, the technical level has been continuously improved, but the luminous efficiency is still from 30 lm/W to 60 lm. /W and then to the development process of 100lm/W, no matter from the "quality" and "quantity", domestic LED light sources are far from meeting the market demand.
When the domestic LED light source PN junction works at normal temperature, although the theoretical life can reach 100,000 hours, the heat dissipation problem cannot be completely and effectively solved, so that its actual life is greatly reduced, and the light decay (life) problem of LED street lamps has also become One of the key issues that restrict its widespread use in streetlights. At present, there is no experience in the service life of LED street lamps. Many manufacturers using domestic LED light sources can claim a life of 50,000 to 60,000 hours, but there is no actual application data or laboratory test data to support them. In actual application, some manufacturers Due to the large light decay, a large number of "dead lights" appeared in a short period of time, causing serious damage to the reputation of LED street lights.
3, the power system is unstable
LED driver power supply instability is the industry consensus, in fact it is dragging the LED lighting industry hind legs, because the drive power is an important part of the LED street light, its failure will lead to the failure of the whole lamp. Due to the harsh environment of outdoor work, the life of some components of the power supply becomes the bottleneck of the life of the driving power source or even the entire street lamp.
The poor reliability of the power supply may cause the installed street lamp to be broken in a short time. This is difficult for the outdoor high-rise device such as the LED street lamp, and the maintenance is more difficult. For the street lamp manufacturer, the unstable power supply makes the maintenance cost. Climb up. Therefore, the quality of high-power LED street lamp driving power supply has become a short board that hinders the development of high-power LED street lamps.
Cr12 Soldering lron,high strength and wear resistance.The cut surface of DIN Rail is smooth and free of burrs.With the 50cm lengthgraduated scale,cutting is accurate.The bezelcan be rotated at 90°,making cutting more convenient.Locking mechanism,humanized design, concenient for storage and transportation.
Crimp Tool WKC8 SeriesSuitable for VE ferrulesWKC8 10-4 Square shape after crimpedWKC8 6-6 Hexagon shape after crimped
Cutting plier ToolSuitable for cutting FBS, JEB bridges
Automatic wire stripping and crimping machineProduct introduction
This model is designed for crimping tube terminal, suitable for wires with cross section 0.5-4mm².Thedesktop type machine is space saving,Theproductionof wiring harness has strong mobility, vibration plate feeding, automatic trigger start,stripping Integratedoperation of stripping wire, insert into ferrules andcrimping is convenient and quick.It is suitable forcrimping, stripping variety of single-grain tubeterminals to wires at one time.
Touch man-machine interface numerical control operation
Stripping through the terminal without reverse wire
Horizontal crimping from left and right
Fool-proof design automatically triggers to start
Holder Bracket For Din Rail,Electric Din Rail Holder,Standard Din Rail Accessories,Din Rai Power Supply
Wonke Electric CO.,Ltd. , https://www.wkdq-electric.com